250W Single Phase MCP Evaporative Cooler Motor
- Power: 250W (1/3 HP) High Torque
- Voltage: 115V/220V Dual Voltage Option
- Insulation: Class H (180°C Rated)
- Application: Evaporative Coolers / HVAC
Contact Us
50KTYZ High Torque Micro Permanent Magnet Synchronous Motor
- Voltage: 220V AC 50Hz/60Hz
- RPM: Low Speed (1-30 RPM Range)
- Stall Protection: Self-Lubricated Gear Box
- Application: Air Louvers, Dampers, Valves
Contact Us
YE3-160L-4 Premium Efficiency 15KW 3-Phase AC Motor
- Efficiency Standard: IE3 Ultra Premium
- Housing: Cast Iron / Heavy Duty Frame
- Enclosure: IP55 Dust & Water Tight
- Winding: 100% Pure Electrolytic Copper
Contact Us
Precision AC Induction Gear Motor (6W - 400W Series)
- Power Range: 6W, 15W, 25W, 90W to 400W
- Gear Reduction: High Gear Ratio Helical Sets
- Duty Cycle: S1 Continuous Heavy Industrial
- Control: Speed Regulator Compatible
Contact Us
IE2 Industrial Single-Phase AC Induction Heavy-Duty Motor
- Design: Energy-Saving High Torque Output
- Capacitor: Dual Capacitor Start / Run
- Surge Protection: Built-in Thermal Cutoff
- Application: Fluid Pumps, Blowers, Mills
Contact Us
YC Series Heavy-Duty Single Phase Motor (0.5HP - 10HP)
- Frame: YC90S-4 High Starting Torque
- Voltage: 220V 50Hz (Iraqi Standard Grid)
- Bearings: Premium C&U / SKF Sealed Bearings
- Application: Commercial Air Units & Tools
Contact Us
1.5KW / 2HP Lightweight Aluminum Shell AC Inverter Motor
- Body: Die-cast Aluminum Heat-Dissipating
- Poles: 2-Pole High Speed (2800+ RPM)
- VFD Compatible: Reinforced Insulation
- Application: Compressors & Industrial Fans
Contact Us
6RPM Ultra-Low Speed High Torque AC Synchronous Drive
- Speed: 6 RPM Constant Speed Sync
- Torque: High Hold Torque Gear Mechanism
- Enclosure: Compact Sealed Housing
- Application: Automation & Domestic Devices
Contact Us
50+
Years Manufacturing Excellence
55°C
Ambient Thermal Rating
IP55+
Sand & Moisture Protection
±20%
Wide Voltage Sag Tolerance
Technical Whitepaper: Fractional Horsepower Electric Motor Engineering for the Iraqi Climate & Industrial Environment
Operating fractional horsepower (FHP) electric motors, geared drives, and centrifugal air blowers in Iraq presents a unique nexus of extreme physical and electrical stresses. From the heavy industrial zones of Basra and the agricultural pumping infrastructure along the Tigris-Euphrates basin, to the commercial cooling requirements of Baghdad, Mosul, and Erbil, electric motors must perform under conditions that routinely break standard catalogue-spec equipment.
Key Engineering Metric for Iraq: Standard electric motors are rated for 40°C maximum ambient temperature. In Central and Southern Iraq, ambient temperatures routinely breach 50°C to 54°C in summer. Coupled with direct solar radiation on outdoor equipment enclosures, internal winding temperatures can rise beyond 155°C without proper Class H insulation and optimized thermal dissipation.
Grid Voltage Sags & Generator Phase Fluctuations
The municipal power distribution network in Iraq frequently experiences severe voltage sags, dropping standard 220V 50Hz single-phase supply down to 170V–180V during peak cooling months. Additionally, switching between central power and localized diesel generators introduces severe voltage spikes and frequency variances. Our FHP motors serving Iraq are built with high magnetic saturation silicon steel laminations and dual-run capacitors, maintaining rated torque output down to 180V without causing rotor stall or overheating.
Heavy Desert Sand & Dust Ingress Protection (IP55/IP66)
Micro-fine airborne particulate matter (dust storms or "Shamal" winds) poses an extreme threat to bearing race integrity and motor winding insulation. Our specialized export motors for the Iraqi market feature double-lip viton shaft seals, sealed-for-life premium C&U/SKF ball bearings filled with high-temperature synthetic polyurea grease, and vacuum-pressure impregnated (VPI) copper windings that prevent particulate abrasion and short-circuiting.
Primary OEM Application Scenarios Across Iraq’s Commercial & Industrial Sectors
Custom-engineered FHP motors and centrifugal air-movement assemblies are critical components in several rapidly expanding sectors across the provinces of Iraq:
| Application Sector |
Primary Technical Requirement |
Common Motor Configuration |
Iraq Regional Focus |
| Evaporative "Desert" Coolers & HVAC |
Moisture-resistant, high start torque under voltage drop, continuous S1 duty. |
250W–750W Single-Phase MCP Shaded Pole / PSC Motors with Class H insulation. |
Baghdad, Basra, Najaf, Karbala |
| Cold Storage & Refrigeration Units |
Low-noise, low vibration, sub-zero continuous duty, automatic louver movement. |
50KTYZ / AC Synchronous motors & Shaded Pole Geared Motors. |
Erbil, Sulaymaniyah, Mosul |
| Fluid Pumps & Water Transfer |
High starting torque, dual capacitor run, corrosion-resistant shaft extensions. |
YC Series 1HP–5HP Heavy Duty Capacitor Start Single-Phase Motors. |
Al-Anbar, Al-Muthanna, Dhi Qar |
| Industrial Automation & Conveyors |
High gear reduction ratios, right-angle spatial efficiency, inverter speed control. |
Inline Helical & Worm Geared Motors (6W to 1.5KW) with aluminum shell. |
Basra Free Zone, Erbil Industrial Zone |
Technical Deep Dive: Evaporative Cooler & Ventilation Motor Engineering
Evaporative air cooling remains the predominant, cost-effective residential and commercial cooling technology throughout Central and Southern Iraq due to low relative summer humidity. However, standard motors operating inside these cooler housings face high humidity air streams combined with 50°C+ ambient intake air. Our OEM 250W MCP cooler motors feature electro-coated anti-corrosion stator housings, moisture-sealed terminal blocks, and internal automatic thermal overload protectors calibrated specifically to disengage at 130°C before permanent copper enamel degradation occurs.
Iraqi Industrial Revitalization: Key Market Trends Driving Motor Procurement
Iraq is undergoing a major industrial shift driven by national infrastructure reconstruction, private sector food processing investment, and public facility modernizations. As an OEM buyer or electrical distributor in Iraq, staying ahead of these trends requires sourcing motors that align with new grid standards and operational realities:
1. Transition Toward Premium Efficiency Standards (IE2/IE3)
With industrial electricity tariffs increasing and reliance on private generator diesel power costing up to four times standard grid electricity, Iraqi factories in Basra and Erbil are aggressively upgrading from legacy rewound motors to high-efficiency IE2 and IE3 three-phase asynchronous motors (such as the YE3 series). Power savings of 3% to 7% across continuous duty cycles yield full motor payback within 8 to 12 months of operation.
2. Modular Inverter & VFD Compatibility
Variable Frequency Drives (VFDs) are increasingly installed across Iraqi textile, bottling, and HVAC plants to regulate airflow and fluid pumping speeds dynamically. Sourcing FHP motors with inverter-duty spike-resistant magnet wire and insulated non-drive end bearings is crucial to eliminate electrical bearing fluting caused by VFD-induced common-mode voltages.
Factory Strengths & Manufacturing Quality Assurance
Since 1974, our manufacturing facility (Delco Fans Pvt. Ltd.) has delivered application-driven electric motors, geared drives, and centrifugal blowers for worldwide OEM integration. We do not operate as a mere catalogue trader; every unit dispatched to our partners in Iraq is backed by extensive shop-floor validation and in-house component engineering.
- In-House Tooling & Stator Punching: Total metallurgical control over cold-rolled silicon steel laminations ensures minimal core losses and lower heat generation.
- 100% Electrolytic Pure Copper Winding: We strictly avoid copper-clad aluminum (CCA). All stators are wound with high-purity Grade 2 enamelled copper wire rated to 180°C (Class H).
- Dynamic Rotor Balancing (ISO 1940 Grade G2.5): Every rotor assembly is dynamically balanced to eliminate high-speed vibration, protecting bearings and reducing operational sound levels below 48 dB.
- Vacuum Pressure Impregnation (VPI): Insulating varnish deeply penetrates stator slots, bonding windings into a solid, moisture-proof, and dust-resistant mass.
- Full-Load Routine Testing: 100% of production units undergo no-load, full-load, locked-rotor, dielectric withstand, and high-voltage flash testing prior to export packing.
- Custom OEM Adaptations: Custom shaft lengths, keyways, threaded ends, mounting flange dimensions, and lead wire harness terminations configured to client drawings.
What electrical frequency and voltage specifications should we specify for Iraq?
Iraq operates on a nominal standard grid of 220V / 230V AC single-phase and 380V / 400V AC three-phase at 50Hz frequency. However, because local diesel generators may fluctuate between 48Hz and 52Hz, we engineer our motors with wide-band tolerance coils designed to operate safely between 180V and 245V without overheating or stalling.
How do your motors handle the extreme summer temperatures in Basra and Baghdad?
Standard commercial motors utilize Class B (130°C) or Class F (155°C) insulation. For the Iraqi market, we utilize Class H (180°C) enamelled copper wire paired with high-temperature synthetic grease in double-sealed SKF/C&U bearings. This guarantees a thermal headroom safety margin of at least 25°C to 30°C even when ambient air temperatures exceed 52°C.
Can you provide custom shaft dimensions and mounting flanges to replace existing motors?
Yes. We specialize in OEM retrofit engineering. Send us your CAD drawings or physical sample specs (shaft diameter, flat spots, threading, bolt hole circle diameter, and housing length), and our engineering team will produce exact drop-in replacement motors tailored for your equipment assembly lines.
What sea and air freight shipping routes do you utilize for deliveries into Iraq?
We routinely arrange international container shipping via sea freight to the Port of Umm Qasr (South Iraq) for commercial shipments heading to Basra, Baghdad, and Central provinces. For the Kurdistan Region (Erbil, Sulaymaniyah), we coordinate sea-land transport via Mersin/Ibrahim Khalil or direct air freight to Erbil International Airport (EBL).
What is the Minimum Order Quantity (MOQ) for custom OEM fractional horsepower motors?
For standard off-the-shelf catalog frame sizes, our MOQ starts as low as 50 to 100 units. For fully customized stator laminations, special shaft machining, or custom housing extrusions, typical OEM batch production runs start at 500 units. Sample evaluation units are available upon technical drawing sign-off.
How do you ensure motor windings do not short-circuit due to fine sand and dust accumulation?
All stators destined for Iraq undergo a specialized double Vacuum Pressure Impregnation (VPI) dipping process. This encapsulates the copper windings in a hard, non-porous resin matrix that prevents micro-abrasions from airborne silica sand while providing superior dielectric isolation.
Partner with a Trusted Electric Motor Manufacturer Serving Iraq
Whether you require bulk supply of 250W cooler motors, IE3 high-efficiency industrial motors, or custom geared drives engineered for high ambient temperatures, our engineering team is ready to assist your procurement.
Contact Us
